SN74LS74AN
| Parameters | |
|---|---|
| Weight | 927.99329mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74LS |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.75V~5.25V |
| Frequency | 33MHz |
| Base Part Number | 74LS74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 25mA |
| Nominal Supply Current | 25mA |
| Output Current | 8mA |
| Number of Bits | 2 |
| Clock Frequency | 33MHz |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 13 ns |
| Logic Function | AND, D-Type, Flip-Flop, Latch |
| Current - Quiescent (Iq) | 8mA |
| Current - Output High, Low | 400μA 8mA |
| Number of Bits per Element | 1 |
| Max Frequency | 33MHz |
| Max Propagation Delay @ V, Max CL | 25ns @ 2.5V, 15pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -400μA |
| Low Level Output Current | 8mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 17 hours ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
SN74LS74AN Overview
The flip flop is packaged in 14-DIP (0.300, 7.62mm). D flip flop is embedded in the Tube package. Currently, the output is configured to use Differential. In the configuration of the trigger, Positive Edgeis used. There is an electric part mounted in the way of Through Hole. A voltage of 4.75V~5.25Vis used as the supply voltage. It is at 0°C~70°C TAdegrees Celsius that the system is operating. It is an electronic flip flop with the type D-Type. The 74LSseries comprises this type of FPGA. Its output frequency should not exceed 33MHz. The list contains 2 elements. As a result, it consumes 8mA quiescent current and is not affected by external forces. The 74LS74 family contains this object. Through Hole mounts this electronic component. A total of 14pins are provided on this board. This device exhibits a clock edge trigger type of Positive Edge. Flip flops designed with 2bits are used in this part. Its flexibility is enhanced by 2 circuits. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 8mA. To operate, the chip has a total of 1 output lines. A total of 3input lines have been provided. In this case, the high level output current is set to -400μA. In the low level output current setting, 8mAis used. Ideally, the operating temperature should be below 70°C. A temperature above 0°Cshould be used for the operation. A minimum supply voltage of 4.75V is required for these RS flip flops to operate. There is a maximum supply voltage of 5.25V. 33MHzis the maximum frequency that can be achieved. Currently, there are 2 channels available.
SN74LS74AN Features
Tube package
74LS series
14 pins
2 Bits
SN74LS74AN Applications
There are a lot of Texas Instruments SN74LS74AN Flip Flops applications.
- Latch
- Data transfer
- Supports Live Insertion
- Single Up Count-Control Line
- Counters
- Frequency Divider circuits
- Common Clocks
- Differential Individual
- Latch-up performance
- Consumer
