SN74LV273APWE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74LV |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LV273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 22.1 ns |
| Turn On Delay Time | 4.8 ns |
| Family | LV/LV-A/LVX/H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20μA |
| Current - Output High, Low | 12mA 12mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LV273APWE4 Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. It is included in the package Tube. T flip flop is configured with an output of Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountis occupied by this electronic component. A 2V~5.5Vsupply voltage is required for it to operate. Temperature is set to -40°C~125°C TA. This D latch has the type D-Type. In FPGA terms, D flip flop is a type of 74LVseries FPGA. You should not exceed 160MHzin its output frequency. D latch consists of 1 elements. As a result, it consumes 20μA of quiescent current without being affected by external factors. A total of 20 terminations have been made. The object belongs to the 74LV273 family. A voltage of 2.5V provides power to the D latch. A 2pFfarad input capacitance is provided by this T flip flop. Electronic devices of this type belong to the LV/LV-A/LVX/Hfamily. Surface Mount mounts this electronic component. As you can see from the design, it has pins with 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. There are 8bits in its design. It reaches 5.5Vwhen the supply voltage is maximal (Vsup). Normally, the supply voltage (Vsup) should be kept above 2V. 8 circuits are used to achieve its superior flexibility. The power supply is 3.3V. With an output current of 12mA, this device offers maximum design flexibility. 2input lines are available for you to choose from.
SN74LV273APWE4 Features
Tube package
74LV series
20 pins
8 Bits
3.3V power supplies
SN74LV273APWE4 Applications
There are a lot of Texas Instruments SN74LV273APWE4 Flip Flops applications.
- Data Synchronizers
- ESCC
- EMI reduction circuitry
- ATE
- ESD performance
- Test & Measurement
- Storage Registers
- Bus hold
- Consumer
- Event Detectors
