SN74LVC574APWG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Frequency | 150MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 7.8 ns |
| Turn On Delay Time | 7 ns |
| Family | LVC/LCX/Z |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Control Type | ENABLE LOW |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVC574APWG4 Overview
TSSOPis the way it is packaged. In total, it contains 1 elements. It has been determined that there have been 20 terminations. The power supply voltage is 1.8V. This D flip flop belongs to the family of LVC/LCX/Z. There is an electronic part that is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device exhibits a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. In light of its reliable performance, this T flip flop is well suited for TUBE. A total of 3.3V power supplies are needed to run it. This D flip flop is equipped with 0 ports. A high level output current of -24mAis set. It is set to 24mAfor low level output current. Operating temperatures should be lower than 125°C. It should be higher than -40°Cwhen the system is operating. The minimum voltage required for operation is 1.65V. 3.6Vis its maximum supply voltage. It is possible to achieve 150MHz frequencies. The logic IC it adopts is BUS DRIVER. A total of 1 functions are provided by this T flip flop. This device is equipped with a pin count of 20. It offers maximum design flexibility with its output current of 24mA.
SN74LVC574APWG4 Features
20 pins
3.3V power supplies
1 Functions
20 pin count
SN74LVC574APWG4 Applications
There are a lot of Texas Instruments SN74LVC574APWG4 Flip Flops applications.
- Shift Registers
- Consumer
- Latch
- Buffered Clock
- Single Down Count-Control Line
- Single Up Count-Control Line
- Latch-up performance
- Memory
- Set-reset capability
- Divide a clock signal by 2 or 4
