SN74S374N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74S |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74S374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Number of Ports | 2 |
| Output Current | 20mA |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 8 ns |
| Family | S |
| Logic Function | D-Type, Latch |
| Current - Quiescent (Iq) | 110mA |
| Current - Output High, Low | 6.5mA - |
| Max I(ol) | 0.02 A |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 15pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74S374N Overview
The flip flop is packaged in a case of 20-DIP (0.300, 7.62mm). It is included in the package Tube. This output is configured with Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. Through Holeis occupied by this electronic component. Powered by a 4.75V~5.25Vvolt supply, it operates as follows. In the operating environment, the temperature is 0°C~70°C TA. There is D-Type type of electronic flip flop associated with this device. JK flip flop belongs to the 74Sseries of FPGAs. In order for it to function properly, its output frequency should not exceed 100MHz. A total of 1 elements are present. T flip flop consumes 110mA quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on 74S374. The D flip flop is powered by a voltage of 5V . An electronic device belonging to the family Scan be found here. There is an electronic part mounted in the way of Through Hole. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is included in FF/Latches. 8bits are used in its design. To achieve this superior flexibility, 8 circuits are used. It runs on 5Vvolts of power. A total of 2ports are embedded in the D flip flop. For high efficiency, the supply voltage should be set to 5V. It offers maximum design flexibility with its output current of 20mA. This input has 3lines in it.
SN74S374N Features
Tube package
74S series
20 pins
8 Bits
5V power supplies
SN74S374N Applications
There are a lot of Texas Instruments SN74S374N Flip Flops applications.
- Control circuits
- Balanced Propagation Delays
- Common Clocks
- Modulo – n – counter
- Matched Rise and Fall
- Set-reset capability
- Data transfer
- Count Modes
- Latch-up performance
- Automotive
