TL1454ACNSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 2MHz |
| Base Part Number | TL1454 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 20V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 20V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 40mA |
| Voltage - Supply (Vcc/Vdd) | 3.6V~20V |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 3.6V |
| Topology | Buck, Boost, Flyback |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 50kHz~2MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PHASE-SHIFT |
| Duty Cycle (Max) | 100% |
| Clock Sync | No |
| Output Phases | 1 |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL1454ACNSR Overview
Capsuled in the 16-SOIC (0.209, 5.30mm Width) package, the switching controller can be used for a wide range of applications. For 2 outputs, the dc motor controller is appropriate. PMIC packaging is solid with a Cut Tape (CT) enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. 3.6V~20V is the operating voltage and supply voltage of the dc control. A -20°C~85°C TA dc switcher is not a problem. The switching controller can be switched at 50kHz~2MHz. dc dc regulator is made easier with Surface Mount. In order to control switching efficiently, the dcdc regulator features Dead Time Control, Frequency Control. Thare switch converters are connected to an analog integrated circuit (IC) of type DUAL SWITCHING CONTROLLER. Switching converters are designed with the terminal (s) at position DUAL . 16 terminations with various dc switching's functions. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. 6V nominal DC switcher's voltage input. Other relevant dc to dc converter ics can be found by searching "TL1454". 16 pins are present on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. It is recommended to use 3.6V as the minimum input voltage of dc dc voltage regulator. According to the test statistics, DC regulator outputs 20V voltage. In most cases, the output current of the dc dc regulator will be 40mA, so note that when you start the project. DC switcher's Surface Mount qualifies it for most applications and prototypes. Switching controller operates at 2MHz Hz. Users should apply 20V to operate the voltage regulator dc to dc safely and reliably.
TL1454ACNSR Features
Transistor Driver Outputs
Switching Frequency: 50kHz~2MHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Frequency: 2MHz
TL1454ACNSR Applications
There are a lot of Texas Instruments TL1454ACNSR DC to DC converter applications.
- Smoke prevention equipment
- Production lines
- Flaw detection equipment
- Computer rooms
- ATMs
- Window air conditioners
- Wind power
- Elevator lighting
- Servo drive system
- Scientific testing
