TL2845P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 440.409842mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Frequency | 500kHz |
| Base Part Number | TL2845 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 30V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7.6V~30V |
| Control Features | Frequency Control |
| Topology | Boost, Flyback, Forward |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | Up to 500kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 50ns |
| Supply Current-Max (Isup) | 30mA |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 50 ns |
| Nominal Input Voltage | 5.5V |
| Max Duty Cycle | 48 % |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL2845P Overview
Capsuled in the 8-DIP (0.300, 7.62mm) package, the switching controller can be used for a wide range of applications. 1 outputs are supported by the dc motor controller. There is a Tube solid enclosure around the pmic. The program can handle Transistor Driver dc switching's outputs (s). The supply and operating voltage of the dc control are 7.6V~30V. A -40°C~85°C TA dc switcher is not a problem. A switching controller such as this can switch at a value of Up to 500kHz . dc dc regulators can be carried out with Through Hole. Frequency Control provides dcdc regulator efficient switching control. An analog IC with the SWITCHING REGULATOR signal is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. Various 8 terminations. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input is 15V. Other relevant dc to dc converter ics can be found by searching "TL2845". The switching converter has a total of 8 pins. In particular, switching converter is a type of Switching Regulator or Controllers. According to the test statistics, DC regulator outputs 30V voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 200mA. A duty cycle set at 48 % ensures voltage regulator dc to dc reliability during power-on and power-off. The switching controller works at a frequency of 500kHz. Input voltage can be set to 5.5V for nominal working status. Switching controller is necessary to provide a voltage of 15V. You should not supply more current than 30mA to the controller.
TL2845P Features
Transistor Driver Outputs
Switching Frequency: Up to 500kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 48 %
Frequency: 500kHz
TL2845P Applications
There are a lot of Texas Instruments TL2845P DC to DC converter applications.
- Balance equipment
- Hydro power
- Electrical distribution systems
- Adjustable voltage or current linear circuits
- Series voltage regulation circuits
- Surge protection circuits
- Electric water heaters
- seismic instrument power circuits
- Remotely powered electric motors
- Automatic testing equipment
