TL5001CP-P
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 440.409842mg |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 2.54mm |
| Base Part Number | TL5001 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 50V |
| Output Type | Transistor Driver |
| Max Output Current | 3A |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 3A |
| Voltage - Supply (Vcc/Vdd) | 3.6V~40V |
| Quiescent Current | 1.1mA |
| Control Features | Dead Time Control, Frequency Control |
| Max Output Voltage | 50V |
| Topology | Buck, Boost, Flyback |
| Min Input Voltage | 3.6V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 20kHz~500kHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 1V |
| Switcher Configuration | SINGLE |
| Max Frequency | 500kHz |
| Duty Cycle (Max) | 100% |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL5001CP-P Overview
The switching controller fits in the 8-DIP (0.300, 7.62mm) package and is ideal for most applications. This dc motor controller can be used to generate outputs with 1 numbers. There is a Tube solid enclosure around the pmic. The system can process Transistor Driver dc switching's outputs (s). 3.6V~40V is the operating voltage and supply voltage of the dc control. Qualified to work in a -20°C~85°C TA dc switcher. Switching can be done at 20kHz~500kHz with this switching controller. The Through Hole value makes it suitable for general dc dc regulator. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a DUAL terminal on the switching converters. The 8 terminations can be used for a wide range of dc switching. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 6V. Searching "TL5001" will return other relevant dc to dc converter ics. Total pins of switching converter are 8. Switching converter is a type of Switching Regulator or Controllers in particular. Based on the test statistics, DC regulator outputs voltage 50V. In most cases, the dc dc regulator's output current is 3A. This information should be noted when you begin working with the component. DC regulator500kHz has the maximum frequency. For safe and reliable operation in a circuit, voltage regulator dc to dc is suggested that users apply 40V. A dc switching in a dormant state uses 1.1mA. Because the dc switcher's maximum input voltage is 40V users must limit the voltage accordingly. The supply voltage must be 3.6V. Output current will not exceed 3A. Datasheets state the switching converter can output up to 50V volts. A voltage controller's lowest output voltage cannot be less than 1V.
TL5001CP-P Features
Transistor Driver Outputs
Switching Frequency: 20kHz~500kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
TL5001CP-P Applications
There are a lot of Texas Instruments TL5001CP-P DC to DC converter applications.
- Printing equipment
- Television equipment
- Wind power
- Medical monitoring systems
- Medical equipment
- Elevator lighting
- Milling machines
- Series voltage regulation circuits
- Current source circuits
- Wide-range voltage regulation circuits
