TL5001CPSR
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 122.611688mg |
| Operating Temperature | -20°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 500kHz |
| Base Part Number | TL5001 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 50V |
| Output Type | Transistor Driver |
| Max Output Current | 3A |
| Operating Supply Voltage | 40V |
| Input Voltage-Nom | 6V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20mA |
| Voltage - Supply (Vcc/Vdd) | 3.6V~40V |
| Quiescent Current | 1.1mA |
| Control Features | Dead Time Control, Frequency Control |
| Max Output Voltage | 50V |
| Topology | Buck, Boost, Flyback |
| Min Input Voltage | 3.6V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 20kHz~500kHz |
| Max Input Voltage | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | No |
| Min Output Voltage | 1V |
| Switcher Configuration | SINGLE |
| Duty Cycle (Max) | 100% |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
TL5001CPSR Overview
Capsuled in the 8-SOIC (0.209, 5.30mm Width) package, the switching controller suits most application needs. 1 outputs can be generated with the dc motor controller. PMIC packaging is solid with a Cut Tape (CT) enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. This dc control operates at 3.6V~40V and has a 3.6V~40V supply voltage. Suitable for a -20°C~85°C TA dc switcher. Switching can be done at 20kHz~500kHz with this switching controller. The Surface Mount allows it to be used for dc dc regulator in general. Featured in the dcdc regulator is Dead Time Control, Frequency Control which allows efficient switching control. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. There are a DUAL terminal on the switching converters. A variety of dc switching's functions can be performed on 8 terminations. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. DC switcher's input voltageis 6V volts. Other relevant dc to dc converter ics will be returned if you search "TL5001". There are only 8 pins on switching converter. According to the test statistics, DC regulator outputs 50V voltage. If you start a project, note down the dc dc regulator's usual output current of 20mA. The switching controller works at a frequency of 500kHz. A circuit should contain 40V in order to ensure the voltage regulator dc to dc runs safely and reliably. DC switching uses 1.1mA when it is dormant. The maximum input voltage of dc switcher is 40V, so users should limit their voltage accordingly. Voltage 3.6V must be supplied. DC switcher will not be able to provide an output current above 3A volts. Datasheets state the switching converter can output up to 50V volts. 1V voltage output is lower than 1V.
TL5001CPSR Features
Transistor Driver Outputs
Switching Frequency: 20kHz~500kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Frequency: 500kHz
TL5001CPSR Applications
There are a lot of Texas Instruments TL5001CPSR DC to DC converter applications.
- Electric water heaters
- Electrical distribution systems
- Game consoles
- Refrigerators of central air conditioners
- Production lines
- Scientific testing
- Flaw detection equipment
- Special machining machine tools
- Industrial controllers
- Drilling machines
