TL598CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 300kHz |
| Base Part Number | TL598 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 12V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7V~40V |
| Control Features | Dead Time Control, Frequency Control |
| Input Voltage (Min) | 7V |
| Topology | Buck, Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100kHz |
| Input Voltage (Max) | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 60ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 35 ns |
| Max Duty Cycle | 45 % |
| Clock Sync | No |
| Output Phases | 1 |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL598CDR Overview
With a 16-SOIC (0.154, 3.90mm Width) package, the switching controller is suitable for a wide range of applications. For 2 outputs, the dc motor controller is appropriate. An enclosure of Tape & Reel (TR) is used to package the PMIC. A total of Transistor Driver dc switching's outputs can be handled by it. 7V~40V is the operating voltage and supply voltage of the dc control. Worked in a 0°C~70°C TA dc switcher before. It can switch at 100kHz. dc dc regulator can be generalized using Surface Mount. Switching control is made easier with the dcdc regulator's Dead Time Control, Frequency Control. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. There are a DUAL terminal on the switching converters. A variety of terminations with 16 of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's input voltageis set to 15V. You can find other relevant dc to dc converter ics by searching "TL598". There are only 16 pins on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. The minimum input voltage of the dc dc voltage regulator should be 7V. DC regulator outputs 12V voltage based on test statistics. Voltages 40V are the maximum that the dc to dc regulator will accept. If you are starting a new project, you should note the dc dc regulator's typical output current is 200mA. voltage regulator dc to dcs with a 45 % duty cycle are designed to be reliable when powered on and powered off. Switching controller operates at 300kHz Hz.
TL598CDR Features
Transistor Driver Outputs
Switching Frequency: 100kHz
Dead Time Control, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 300kHz
TL598CDR Applications
There are a lot of Texas Instruments TL598CDR DC to DC converter applications.
- PSRR circuits
- Boring machines
- Alternators
- Drilling machines
- Digital display device
- Injection molding machinery
- Surface processing equipment
- Industrial controllers
- Gear/thread machining machines
- Thermal power
