TPS40042DRCT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40042 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 4.95V |
| Output Type | Transistor Driver |
| Max Output Current | 15A |
| Operating Supply Voltage | 5.5V |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 1mA |
| Output Configuration | Positive |
| Output Current | 15A |
| Voltage - Supply (Vcc/Vdd) | 3V~5.5V |
| Quiescent Current | 1mA |
| Control Features | Enable |
| Max Output Voltage | 4.95V |
| Topology | Buck |
| Min Input Voltage | 3V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 600kHz |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 600mV |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 700kHz |
| Duty Cycle (Max) | 95% |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40042DRCT Overview
It comes in the 10-VFDFN Exposed Pad package, which makes switching controller suitable for most applications. For outputs of 1, this dc motor controller is suitable. PMIC is packaged in a solid enclosure of Tape & Reel (TR). Transistor Driver dc switching's outputs (s) are supported. The supply and operating voltage of the dc control are 3V~5.5V. Suitable for working in an dc switcher that has a -40°C~85°C TA. In this switching controller, the switch can be set to 600kHz. The Surface Mount allows it to be used for dc dc regulator in general. Enable provides dcdc regulator efficient switching control. SWITCHING CONTROLLER analog IC connects the switch converters. There are a DUAL terminal on the switching converters. A variety of terminations with 10 of dc switching. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input is 5V. Other relevant dc to dc converter ics can be found by searching "TPS40042". There are only 10 pins on switching converter. As determined by the test statistics, the output voltage of DC regulator is 4.95V. In most cases, the dc dc regulator's output current is 15A. This information should be noted when you begin working with the component. The max frequency of the pmic can reach 700kHz. To operate the voltage regulator dc to dc safely and reliably, users should apply 5.5V. DC switchings that are dormant use 1mA. The maximum input voltage of dc switcher is 5.5V, so users should limit their voltage accordingly. There must be a 3V supply voltage. The dc switcher will not provide an output current greater than 15A. Datasheets indicate that the switching converter can output 4.95V volts at its maximum. A supply current of 1mA is used to power it. 600mV voltage output is lower than 600mV.
TPS40042DRCT Features
Transistor Driver Outputs
Switching Frequency: 600kHz
Enable
PULSE WIDTH MODULATION
TPS40042DRCT Applications
There are a lot of Texas Instruments TPS40042DRCT DC to DC converter applications.
- Automatic testing equipment
- Sink circuits
- Electric water heaters
- Balance equipment
- Solar power plants
- Household control circuits
- Industrial robots
- Correction machines
- Production lines
- Linear guide
