TPS40042DRCTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Base Part Number | TPS40042 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 600mV |
| Output Type | Transistor Driver |
| Max Output Current | 15A |
| Operating Supply Voltage | 5.5V |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Operating Supply Current | 1mA |
| Output Configuration | Positive |
| Output Current | 15A |
| Voltage - Supply (Vcc/Vdd) | 3V~5.5V |
| Quiescent Current | 1mA |
| Control Features | Enable |
| Max Output Voltage | 4.95V |
| Topology | Buck |
| Min Input Voltage | 3V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 600kHz |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Min Output Voltage | 600mV |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 700kHz |
| Duty Cycle (Max) | 95% |
| Clock Sync | No |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS40042DRCTG4 Overview
In the 10-VFDFN Exposed Pad package, the switching controller meets most application requirements. There is enough capacity in the dc motor controller to generate the output for the 1 input. Packaged in solid enclosures, this pmic has a Tape & Reel (TR) rating. There are Transistor Driver dc switching's output (s) that it can handle. dc controls with 3V~5.5V voltage are supplied and operated. Work well in dc switchers with a -40°C~85°C TA. In this switching controller, the switch can be set to 600kHz. dc dc regulators can be carried out with Surface Mount. Enable is used for efficient switching control in the dcdc regulator. The switch converters are connected to a SWITCHING CONTROLLER analog IC. There are a DUAL terminal on the switching converters. 10 terminations with various dc switching's functions. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 5V. Other relevant dc to dc converter ics can be found by searching "TPS40042". Total pins of switching converter are 10. Statistically, the DC regulator outputs 600mV voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 15A. DC regulator has a maximum frequency of 700kHz. A circuit should contain 5.5V in order to ensure the voltage regulator dc to dc runs safely and reliably. In a dormant state, the dc switching uses 1mA. In order to ensure the dc switcher's functionality, users must limit the voltage to 5.5V due to the dc switcher's maximum input voltage. Voltage 3V is needed for the supply. There will be 15A output current greater than 15A from the dc switcher. Its datasheet indicates the switching converter can output a maximum of 4.95V volts. There is a 1mA volt supply current. The voltage controller's lowest voltage output is not less than 600mV.
TPS40042DRCTG4 Features
Transistor Driver Outputs
Switching Frequency: 600kHz
Enable
PULSE WIDTH MODULATION
TPS40042DRCTG4 Applications
There are a lot of Texas Instruments TPS40042DRCTG4 DC to DC converter applications.
- Access control systems
- Printing equipment
- Grinders
- Automatic plug-in machines
- Communication system
- Current source circuits
- Remotely powered electric motors
- Post equipment
- ATMs
- Correction machines
