TPS40192DRCTG4
| Parameters | |
|---|---|
| Surface Mount | YES |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Packaging | Cut Tape |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.5mm |
| Frequency | 600kHz |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Max Output Current | 15A |
| Input Voltage-Nom | 12V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Current - Output | 15A |
| Quiescent Current | 2.5mA |
| Frequency (Max) | 700kHz |
| Max Output Voltage | 14.4V |
| Voltage - Output | 14.4V |
| Min Input Voltage | 4.5V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 700kHz |
| Max Input Voltage | 18V |
| Control Technique | PULSE WIDTH MODULATION |
| Min Output Voltage | 591mV |
| Switcher Configuration | PUSH-PULL |
| Duty Cycle (Max) | 85 % |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
TPS40192DRCTG4 Overview
The dc motor controller is adquate to generate for 1 outputs. The pmic is packaged in Cut Tape solid enclosure. With this switching controller, you can switch at 700kHz. A SWITCHING CONTROLLER analog IC is connected to the switch converters. Switching converters are designed with the terminal (s) at position DUAL . Different dc switching's functions can be applied to 10 terminations. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 12V. 10 pins are on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. Switching controllers operate at 600kHz frequencies. Keep dc regulator at a temperature of -40°C or above. At a temperature around 85°C degrees Celsius, dc regulator should be running. Total number of functions (s) for thare switch converters are 1. DC switching uses 2.5mA when it is dormant. Voltage regulators switching is designed with 10 pins. Maximum frequency of the controller is 700kHz. Users must limit the voltage accordingly because the dc switcher's maximum input voltage is 18V. With 15A input, it is ideal for switching controllers. This process outputs a value of 14.4V for normalworking processes. 4.5V is the required supply voltage. Input current cannot exceed 15A with this dc switcher. A datasheet states that the switching converter can output 14.4V volts at its maximum. Neither the voltage controller's lowest voltage output 591mVr its highest voltage output is less than 591mV. In terms of maximum supply voltage, switching voltage regulators is rated 18V.
TPS40192DRCTG4 Features
Switching Frequency: 700kHz
PULSE WIDTH MODULATION
Frequency: 600kHz
TPS40192DRCTG4 Applications
There are a lot of Texas Instruments TPS40192DRCTG4 DC to DC converter applications.
- Computed tomography (CT)
- Shearing machines
- Current source circuits
- Surge protection circuits
- Analog precision reference circuits
- Serial communication converter
- Power supplies of electronic gadgets
- Balance equipment
- Telecommunications equipment
- Hydraulic presses
