VN7040AJ-E
| Parameters | |
|---|---|
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerLFSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| Feature | Auto Restart, Status Flag |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.5mm |
| Base Part Number | VN7040 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 24A |
| Supply Voltage-Max (Vsup) | 28V |
| Supply Voltage-Min (Vsup) | 4V |
| Interface | On/Off |
| Nominal Supply Current | 3mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 5mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 120 μs |
| Switch Type | General Purpose |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4V~28V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 40m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
VN7040AJ-E Overview
As a result, it is packaged in the form of a Tube.This package is included in 16-PowerLFSOP (0.154, 3.90mm Width).The lighting driver has the mounting type Surface Mount.General Purpose is the type of switch owned by it.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.As a default, the output is set to 1.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.This LED driving board is equipped with Auto Restart, Status Flag features in order for it to be useful.As you can see, it comes from the VN7040 family.It has a total of 16 terminations.During operation, the 16 pins are used.It is important to note that the LED driving board has 1 functions.The maximum output current is reduced to 24A to meet the operation criteria.The supply voltage of 13V is conducive to high efficiency.In this case, it is mounted in the way of Surface Mount.It belongs to the VIPower? series.The maximum supply voltage is set to 28V.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4V.This system has a maximum current requirement of 5mA.
VN7040AJ-E Features
Supplied from 13V
VN7040AJ-E Applications
There are a lot of STMicroelectronics VN7040AJ-E Power Switches ICs applications.
- Hot Swaps
- Wearable Devices
- Portable/Handheld Devices
- Hot-Swap Systems
- Portable GPS Device
- PC Card Hot Swap
- Portable GPS
- Smartphone and PDA
- Notebook and Tablet Computers
- Wireless Modem Data Cards
