5962-9469203QPA
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Package / Case | CDIP |
| Surface Mount | NO |
| Number of Pins | 8 |
| Packaging | Rail/Tube |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Pin Count | 8 |
| Qualification Status | Qualified |
| Temperature Grade | MILITARY |
| Number of Channels | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 4.4V |
| Power Dissipation-Max | 1.05W |
| Power Dissipation | 1.05W |
| Supply Current-Max | 0.5mA |
| Slew Rate | 0.55 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 800pA |
| Input Offset Voltage (Vos) | 950μV |
| Gain Bandwidth Product | 820 kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 710 kHz |
| Voltage Gain | 114.81dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 8V |
| Low-Bias | YES |
| Micropower | YES |
| Min Dual Supply Voltage | 2.2V |
| Bias Current-Max (IIB) @25C | 0.0005μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 820 kHz |
| Max I/O Voltage | 950μV |
| Wideband | NO |
| Height | 5.08mm |
| Length | 9.6mm |
| Width | 6.67mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
5962-9469203QPA Overview
There is a CDIP case package that contains the instrumentation amplifiers. Op amps are OPERATIONAL AMPLIFIER types of amplifier on the chip. There is a Rail/Tube case that is delivered with the instrumentation amplifiers. The number of terminations approaches 8. A total of 8 pins are located on this board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 8 pins. Op amp rates 950μV as input offset voltage. There should be no change in the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. The temperature should not be lower than -55°C for operational amplifier ics to operate. Instrumentation amplifier should only be used at temperatures up to 125°C. Under 16V is the minimum supply voltage for this electric component. As a rule of thumb, the supply voltage of the op amp should not be lower than 4.4V. This electronic part should be conducted with a dual supply voltage of 8V volts for this part.
5962-9469203QPA Features
8 Pins
supply voltage of 5V
114.81dB voltage gain
5962-9469203QPA Applications
There are a lot of Texas Instruments 5962-9469203QPA Instrumentational OP Amps applications.
- Thermocouples
- Weighing systems
- Proportional operation circuits
- Signal amplification
- Band-pass filter
- Tablets
- pH (acidity)
- Radiation thermometry transducers
- High-frequency data acquisition systems
- Gaming industry
