7200L25JI
| Parameters | |
|---|---|
| Min Supply Voltage | 4.5V |
| Element Configuration | Dual |
| Nominal Supply Current | 80mA |
| Max Supply Current | 80mA |
| Clock Frequency | 28.5MHz |
| Access Time | 25 ns |
| Data Bus Width | 9b |
| Direction | Bidirectional |
| Organization | 256X9 |
| Density | 2.3 kb |
| Standby Current-Max | 0.0005A |
| Parallel/Serial | PARALLEL |
| Sync/Async | Asynchronous |
| Word Size | 9b |
| Memory IC Type | OTHER FIFO |
| Bus Directional | Unidirectional |
| Retransmit Capability | Yes |
| Programmable Flags Support | No |
| Output Enable | NO |
| Cycle Time | 35 ns |
| Height Seated (Max) | 3.55mm |
| Length | 13.97mm |
| Width | 11.43mm |
| Thickness | 2.79mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | PLCC |
| Number of Pins | 32 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 32 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | RETRANSMIT |
| Subcategory | FIFOs |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 32 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
7200L25JI Overview
FIFO memory chip can be found in the PLCC package.Mounting it in Surface Mount is recommended.When the supply voltage is 5V , high efficiency is possible.A total of 32 terminations can be found in FIFO means.Operation pins are 32 .FIFO design requires a maximum current of 80mA to operate.When the supply voltage is set to 5V , the FIFO's maximum efficiency is achieved.The FIFO products must be run at a minimum temperature of -40°C degrees Celsius to ensure reliability.The memory logic's maximum operating temperature is 85°C °C, which allows for stable operation.A self-contained gadget is contained within FIFOs .The IC of the part is OTHER FIFO memory type.The FIFO memory chip may be operated at very low supply voltages, such as4.5V volts.The memory logic's maximum supply voltage is 5.5V volts.It has a total of 32 pins on it.Normally, the component owns 5V power supplies.It is also possible to generate RETRANSMIT using this FIFO memory.A clock on the FIFO memory IC runs at a frequency of 28.5MHz .
7200L25JI Features
FIFOs category
Clock frequency of 28.5MHz
7200L25JI Applications
There are a lot of Integrated Device Technology (IDT) 7200L25JI FIFOs Memory applications.
- One assembly
- TVs
- Firmware loaders
- Multimedia
- Tape controllers
- Application that requires re-writable nonvolatile parameter memory
- Data communications
- Address mapping
- Fabrication Site
- PC peripheral
