74ABT823D,602
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ABT823 |
| JESD-30 Code | R-PDSO-G24 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Clock Frequency | 200MHz |
| Family | ABT |
| Current - Quiescent (Iq) | 250μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 32mA 64mA |
| Output Polarity | TRUE |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 9 |
| Max Propagation Delay @ V, Max CL | 6.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Propagation Delay (tpd) | 6.8 ns |
| Power Supply Current-Max (ICC) | 34mA |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
74ABT823D,602 Overview
24-SOIC (0.295, 7.50mm Width)is the way it is packaged. You can find it in the Tubepackage. The output it is configured with uses Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. The electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. It is operating at -40°C~85°C TA. This logic flip flop is classified as type D-Type. In terms of FPGAs, it belongs to the 74ABT series. In order for it to function properly, its output frequency should not exceed 200MHz. A total of 1elements are contained within it. As a result, it consumes 250μA quiescent current. In 24terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. D latch belongs to the 74ABT823 family. A voltage of 5V is used as the power supply for this D latch. A 4pFfarad input capacitance is provided by this T flip flop. It belongs to the family of electronic devices known as ABT. This RS flip flops is a part number FF/Latches. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 4.5V. The D latch runs on a voltage of 5V volts. This flip flop has a total of 2ports. Additionally, there are WITH CLEAR AND CLOCK ENABLE on the electronic flip flop that can be referred to.
74ABT823D,602 Features
Tube package
74ABT series
5V power supplies
74ABT823D,602 Applications
There are a lot of NXP USA Inc. 74ABT823D,602 Flip Flops applications.
- Frequency Dividers
- Memory
- Bus hold
- Digital electronics systems
- Set-reset capability
- Single Up Count-Control Line
- ESCC
- Shift registers
- Data Synchronizers
- QML qualified product
