74ACT534SJ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 100MHz |
| Base Part Number | 74ACT534 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT534SJ Overview
20-SOIC (0.209, 5.30mm Width)is the packaging method. There is an embedded version in the package Tube. As configured, the output uses Tri-State, Inverted. It is configured with a trigger that uses a value of Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. In this case, it is a type of FPGA belonging to the 74ACT series. It should not exceed 100MHzin terms of its output frequency. In total, it contains 1 elements. During its operation, it consumes 40μA quiescent energy. The object belongs to the 74ACT534 family. The input capacitance of this JK flip flopis 4.5pF farads. There is an electronic component mounted in the way of Surface Mount. 20pins are included in its design. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The design is based on 8bits. In order to achieve its superior flexibility, 8 circuits are used. Optimal efficiency requires a supply voltage of 5V. It operates with 3 output lines. It has 8lines. A -24mAvalue is set for the high level output current. It is set to 24mAfor the low level output current. The operating temperature should be lower than 85°C. Ideally, the operating temperature should be greater than -40°C. The RS flip flop is designed to operate with a minimal supply voltage of 4.5VV. 5.5Vis the maximum supply voltage supported by it. This frequency can be achieved at 100MHz.
74ACT534SJ Features
Tube package
74ACT series
20 pins
8 Bits
74ACT534SJ Applications
There are a lot of ON Semiconductor 74ACT534SJ Flip Flops applications.
- Load Control
- CMOS Process
- Test & Measurement
- Pattern generators
- ESCC
- Functionally equivalent to the MC10/100EL29
- Convert a momentary switch to a toggle switch
- Latch-up performance
- Data Synchronizers
- Buffered Clock
