74AHC374D-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74AHC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Base Part Number | 74AHC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 10.1 ns |
| Quiescent Current | 4μA |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
74AHC374D-Q100J Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. A package named Tape & Reel (TR)includes it. As configured, the output uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~5.5V volts. In this case, the operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74AHC series. You should not exceed 120MHzin its output frequency. There are 1 elements in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. The 74AHC374family includes it. Power is provided by a 5V supply. A 3pFfarad input capacitance is provided by this T flip flop. It belongs to the family of electronic devices known as AHC/VHC/H/U/V. It is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. 8bits are used in its design. For normal operation, the supply voltage (Vsup) should be above 2V. The D flip flop has no ports embedded. The supply voltage should be maintained at 5V for high efficiency. 8input lines are available for you to choose from. Despite external influences, it consumes 4μAof quiescent current.
74AHC374D-Q100J Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
74AHC374D-Q100J Applications
There are a lot of Nexperia USA Inc. 74AHC374D-Q100J Flip Flops applications.
- Cold spare funcion
- Digital electronics systems
- QML qualified product
- Test & Measurement
- Safety Clamp
- Memory
- Matched Rise and Fall
- Bus hold
- Guaranteed simultaneous switching noise level
- Buffer registers
