74F74PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Supplier Device Package | 14-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 125MHz |
| Base Part Number | 74F74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Output Current | 20mA |
| Number of Bits | 2 |
| Clock Frequency | 125MHz |
| Propagation Delay | 8 ns |
| Turn On Delay Time | 5.3 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 16mA |
| Current - Output High, Low | 1mA 20mA |
| Number of Gates | 2 |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F74PC Overview
As a result, it is packaged as 14-DIP (0.300, 7.62mm). You can find it in the Tubepackage. There is a Differentialoutput configured with it. In the configuration of the trigger, Positive Edgeis used. Through Holeis in the way of this electric part. With a supply voltage of 4.5V~5.5V volts, it operates. A temperature of 0°C~70°C TAis considered to be the operating temperature. This D latch has the type D-Type. JK flip flop belongs to the 74Fseries of FPGAs. You should not exceed 125MHzin the output frequency of the device. There are 2 elements in it. There is 16mA quiescent consumption. It is a member of the 74F74 family. There is an electronic part that is mounted in the way of Through Hole. It is designed with 14 pins. The clock edge trigger type for this device is Positive Edge. Flip flops designed with 2bits are used in this part. Its flexibility is enhanced by 2 circuits. High efficiency requires the supply voltage to be maintained at 5V. The 20mA output current allows it to be designed with the greatest amount of flexibility. There are 2 output lines in this JK flip flop. This input has 4lines. -1mAis set as the high level output current. 20mA is the low level output current. A temperature below 70°Cis recommended for operation. Ideally, the operating temperature should be greater than 0°C. The minimum voltage required for operation is 4.5V. 5.5Vis the maximum supply voltage it supports. It is possible to achieve a frequency of 125MHz. There are 2 gates in its basic building block.
74F74PC Features
Tube package
74F series
14 pins
2 Bits
2 gates
74F74PC Applications
There are a lot of ON Semiconductor 74F74PC Flip Flops applications.
- Data storage
- Count Modes
- Load Control
- Set-reset capability
- Registers
- ATE
- Latch-up performance
- Bus hold
- Buffered Clock
- Frequency Divider circuits
