74HC174DB,112
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Published | 2013 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 107MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 16 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 6 |
| fmax-Min | 20 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC174DB,112 Overview
In the form of 16-SSOP (0.209, 5.30mm Width), it has been packaged. D flip flop is embedded in the Tube package. As configured, the output uses Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at a voltage of 2V~6V. In this case, the operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the 74HC series. There should be no greater frequency than 107MHzon its output. A total of 1elements are present in it. As a result, it consumes 8μA quiescent current. Currently, there are 16 terminations. The 74HC174 family contains this object. A voltage of 5V is used to power it. This JK flip flop has a 3.5pFfarad input capacitance. HC/UHis the family of this D flip flop. It is mounted in the way of Surface Mount. A total of 16pins are provided on this board. This device exhibits a clock edge trigger type of Positive Edge. There are 6bits in its design. As soon as 6Vis reached, Vsup reaches its maximum value. A normal operating voltage (Vsup) should remain above 2V. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. 6input lines are available for you to choose from.
74HC174DB,112 Features
Tube package
74HC series
16 pins
6 Bits
74HC174DB,112 Applications
There are a lot of Nexperia USA Inc. 74HC174DB,112 Flip Flops applications.
- Common Clocks
- Dynamic threshold performance
- Parallel data storage
- Digital electronics systems
- Balanced 24 mA output drivers
- Frequency Dividers
- Divide a clock signal by 2 or 4
- Single Up Count-Control Line
- Bounce elimination switch
- Guaranteed simultaneous switching noise level
