A6A259KLBTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Feature | Addressable Latch Mode |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 1.7Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | A6A259 |
| Pin Count | 24 |
| JESD-30 Code | R-PDSO-G24 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 1.1A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | On/Off |
| Output Configuration | Low Side |
| Voltage - Supply (Vcc/Vdd) | 4.5V~5.5V |
| Input Type | Inverting, Non-Inverting |
| Switch Type | Latched Driver |
| Output Current per Channel | 350mA |
| Ratio - Input:Output | 3:8 |
| Voltage - Load | 50V Max |
| Driver Number of Bits | 8 |
| Fault Protection | Current Limiting (Fixed) |
| Output Peak Current Limit-Nom | 2A |
| Rds On (Typ) | 1 Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
A6A259KLBTR Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).In the 24-SOIC (0.295, 7.50mm Width) package, it is included.A Surface Mount mounting is used for the LED driving board.The switch type is Latched Driver.Keeping the temperature at -40°C~125°C TA ensures reliable operation.By default, it is set to output 8.It uses a supply voltage of 4.5V~5.5V to operate.There is a maximum output voltage of N-Channel volts on this LED driver.There are Addressable Latch Mode features available on the LED driving board.I believe it belongs to the A6A259 family.The termination count is 24.As far as functions are concerned, the lighting driver has 1.To comply with the operation criteria, the maximum output current is reduced to 1.1A.High efficiency is possible at 5V supply voltage.It is mounted in the way of Surface Mount.24 pins are connected to it in total.Lighting drivers with 1.7Ohm resistance are used.This LED driver is self-contained in an econtainer with a capacity of Peripheral Drivers.The maximum supply voltage for this LED driver is 5.5V (Vsup).In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 4.5V.5V is the power supply of the part.
A6A259KLBTR Features
Supplied from 5V
Resistance of 1.7Ohm
A6A259KLBTR Applications
There are a lot of Allegro MicroSystems A6A259KLBTR Power Switches ICs applications.
- Solid-State Drives
- Solid State Drivers
- USB Protection
- Portable/Handheld Devices
- USB Ports/Hubs
- Storage (HDDs, SSDs)
- Storage Drives
- Portable GPS
- USB Power Distribution
- Portable Video Game Players
