ADA4000-1AUJZ-R2
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADA4000 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Voltage | 18V |
| Operating Supply Current | 1.35mA |
| Quiescent Current | 1.65mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 8V~36V ±4V~18V |
| Output Current per Channel | 28mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 114dB |
| Average Bias Current-Max (IIB) | 0.003μA |
| Power Supply Rejection Ratio (PSRR) | 82dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00004μA |
| Programmable Power | NO |
| Input Capacitance | 5.5pF |
| Input Voltage Noise Density | 16nV/sqrt Hz |
| Height | 900μm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4000-1AUJZ-R2 Overview
The linear amplifier is packaged in a SOT-23-5 Thin, TSOT-23-5 case which makes it easy for the consumer to handle. An op amp ic of the J-FET type. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. A total of 5 terminations have been reported in the past few weeks. In this case, there are 5 pins on the board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 5 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 200μV. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using an 1.35mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 114dB. There are a total of 1 channels available on the op amps. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. Buffer amplifier has a quiescent current of 1.65mA.
ADA4000-1AUJZ-R2 Features
5 Pins
supply voltage of 5V
114dB voltage gain
ADA4000-1AUJZ-R2 Applications
There are a lot of Analog Devices Inc. ADA4000-1AUJZ-R2 Instrumentational OP Amps applications.
- Power transmission
- Oscilloscopes
- Automatic control
- ECG equipment
- High/low-pass filter circuit
- Navigation
- Exponential operation circuits
- Mobile phone
- Weighing systems
- Hand-held batteries
