ADA4062-2ARMZ-RL
| Parameters | |
|---|---|
| Quiescent Current | 165μA |
| Slew Rate | 3.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 8V~36V ±4V~18V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 1.5mV |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1400 kHz |
| Voltage Gain | 83dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 750μV |
| Settling Time | 3.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Input Capacitance | 4.8pF |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADA4062 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 330μA |
ADA4062-2ARMZ-RL Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. J-FET-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 8-pin op amp ic is included in the package. The input offset voltage is 1.5mV. This electrical part should be mounted using type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . You can run this op amp ic on 330μA . It is recommended to keep the voltage gain at 83dB at all times. 2 channels are available on the instrumentation amplifier. TAPE AND REEL is adopted to pack the instrumentation amplifier. 165μA quiescent currents are flowing through buffer op amp.
ADA4062-2ARMZ-RL Features
8 Pins
supply voltage of 15V
83dB voltage gain
ADA4062-2ARMZ-RL Applications
There are a lot of Analog Devices Inc. ADA4062-2ARMZ-RL Instrumentational OP Amps applications.
- Precision measurement
- Communication
- Integrator circuits
- Medical instruments
- Multimedia playback equipment
- Biopotential
- Voltage regulation circuit
- Portable media players
- Division circuits
- Inverse/same-phase proportional circuit
