Parameters |
Mounting Type |
Surface Mount |
Package / Case |
28-LCC (J-Lead) |
Surface Mount |
YES |
Number of Pins |
28 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
300Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
J BEND |
Peak Reflow Temperature (Cel) |
225 |
Number of Functions |
1 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG506 |
Pin Count |
28 |
Qualification Status |
Not Qualified |
Number of Channels |
16 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
600μA |
Power Dissipation |
10mW |
Propagation Delay |
300 ns |
Turn On Delay Time |
450 ns |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
450 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
300Ohm |
Min Dual Supply Voltage |
10.8V |
Multiplexer/Demultiplexer Circuit |
16:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 44pF |
On-state Resistance Match-Nom |
22.5Ohm |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
15 Ω |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG506AKP Overview
The electronic component is convenient to ship overseas because it is packed in a 28-LCC (J-Lead). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 16:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. There are 28 pins injected into the electronic part body. There are 1 circuits in this switch device. Search with ADG506 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 300Ohm. You can find the functions of the 28 pins in the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 16.5V in normal situations. 10.8V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 600μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. It is recommended that you attach at least 10.8V to your dual power supply. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board.
ADG506AKP Features
16 Channels
600μA Supply Current
ADG506AKP Applications
There are a lot of Analog Devices Inc. ADG506AKP Analog Switches & Multiplexers ICs applications.
- Cable PC
- Automatic test equipment
- Audio signal routing
- Medical Instrumentation
- Signal routing between systems
- ISDN NT1/TA
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Video switching
- Industrial control systems
- Central office