ADG5413BFBRUZ-RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-TSSOP |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 11.5Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 1mW |
| Base Part Number | ADG5413 |
| Polarity | Non-Inverting |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Test Frequency | 1MHz |
| Power Dissipation | 1mW |
| Max Supply Current | 55μA |
| Turn On Delay Time | 202 ns |
| Voltage - Supply, Single/Dual (±) | 8V~44V ±5V~22V |
| Supply Type | Dual, Single |
| Bandwidth | 160MHz |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 270MHz |
| On-State Resistance (Max) | 11.5Ohm |
| Min Dual Supply Voltage | 9V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 11pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 500ns, 515ns |
| Insertion Loss (dB) | -0.6 dB |
| Charge Injection | -640pC |
| Channel-to-Channel Matching (ΔRon) | 50mOhm |
| Crosstalk | -90dB @ 1MHz |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5413BFBRUZ-RL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature around -40°C~125°C TA extended. The analog switch ics are built using SPST - NO/NC switching circuits. It consists of 4 circuits. Look for analog switch ic variants by searching with ADG5413. The internal resistance of this digital multiplexer is 11.5Ohm. For functions related to 16 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 40V. An effective Dual, Single supply digital multiplexer. A low voltage of 9V should be applied to the electronic component. When the digital multiplexer is charged above 55μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 9V voltage attached. The transfer of data can be performed over 160MHz bandwidths. A temperature above 125°C is not suitable for operation of the analogue multiplexer. Suppliers are offering a 16-TSSOP package.
ADG5413BFBRUZ-RL7 Features
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 270MHz
Bandwidth: 160MHz
ADG5413BFBRUZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5413BFBRUZ-RL7 Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Digital Cross-Connects
- Fiber In The Loop (FITL)
- Video switching
- Modems
- Transmit
- Microprocessor Controlled Analog Systems
- E1 Network Equipment
- Cable Modem
- Data switching
