ADG5413FBRUZ-RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 11.5Ohm |
| Max Power Dissipation | 1mW |
| Technology | DMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | ADG5413 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 8V |
| Test Frequency | 1MHz |
| Power Dissipation | 1mW |
| Max Supply Current | 1.2mA |
| Turn On Delay Time | 495 ns |
| Voltage - Supply, Single/Dual (±) | 8V~44V ±5V~22V |
| Supply Type | Dual, Single |
| Bandwidth | 160MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 510 ns |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 270MHz |
| On-State Resistance (Max) | 11.5Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 11pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 500ns, 515ns |
| Insertion Loss (dB) | -0.6 dB |
| Charge Injection | -640pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5413FBRUZ-RL7 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~125°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. There are 16 pins injected into the electronic part body. Unlike digital switches, these are based on SPST - NO/NC switching circuits. The multiplexer consists of 4 circuits. Try searching with ADG5413 if you're looking for variants. In this multiplexer, the internal resistance is 11.5Ohm. To find out what the 16 pins do, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 44V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 8V. If you put voltage higher than 1.2mA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. For dual power supplies, a voltage of at least 5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. A 160MHz-bandwidth can be used for data transfer.
ADG5413FBRUZ-RL7 Features
1 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 270MHz
Bandwidth: 160MHz
ADG5413FBRUZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5413FBRUZ-RL7 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Communication systems
- Cable Modem
- Audio and video switching
- Industrial control systems
- Remote wireless modules
- ISDN NT1/TA
- Sample-and-hold systems
- Microprocessor Controlled Analog Systems
- Frame Relay Equipment
