ADG709BRUZ-REEL
| Parameters | |
|---|---|
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 4.5Ohm |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 2.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 13pF 42pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns (Typ) |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Signal Current-Max | 0.01A |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG709 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 3/5/+-3V |
| Number of Channels | 4 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Throw Configuration | 4PST |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±2.5V |
| Supply Type | Dual, Single |
| Bandwidth | 55MHz |
| Supply Current-Max (Isup) | 0.001mA |
ADG709BRUZ-REEL Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 4:1. Extended operating temperature around -40°C~125°C TA. There are 16 terminations totally. A 4 channel electronic part produces high-quality output. An 2.5V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. Circuits based on SP4T switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 2. Try searching with ADG709 to find analog multiplexer variants. There is 4.5Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1nA would be sufficient for this switch device. 5V operating voltages are supported by the electronic component. There are 8 inputs to be operated. The data can be transferred over a wide range of bandwidths, called 55MHz bandwidths.
ADG709BRUZ-REEL Features
4 Channels
Switch Circuit: SP4T
1nA Supply Current
Bandwidth: 55MHz
ADG709BRUZ-REEL Applications
There are a lot of Analog Devices Inc. ADG709BRUZ-REEL Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Precision test equipment
- Sample hold systems
- Data switching
- Channel Banks
- Video switching
- Microprocessor controlled systems
- Isolation
- Fault Tolerant Systems
- Data Acquisition Systems
