ADG734BRUZ

21ns, 10ns (Typ) SPDT 4.5Ohm Analog Switches BREAK-BEFORE-MAKE ADG734 20 Pins 100pA 2.5V 20-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG734BRUZ
Package: 20-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 789
Description: 21ns, 10ns (Typ) SPDT 4.5Ohm Analog Switches BREAK-BEFORE-MAKE ADG734 20 Pins 100pA 2.5V 20-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 2 weeks ago)
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	20-TSSOP (0.173, 4.40mm Width)
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
ECCN Code	EAR99
Resistance	4.5Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	5μW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	2.5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	ADG734
Pin Count	20
Number of Outputs	8
Polarity	Non-Inverting
Power Supplies	3/5/+-3V
Number of Channels	4
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Test Frequency	1MHz
Operating Supply Current	1nA
Nominal Supply Current	1μA
Power Dissipation	5μW
Max Supply Current	1μA
Turn On Delay Time	34 ns
Voltage - Supply, Single/Dual (±)	1.8V~5.5V ±2.5V
Supply Type	Dual, Single
Bandwidth	160MHz
Neg Supply Voltage-Nom (Vsup)	-2.5V
Turn-Off Delay Time	12 ns
Max Dual Supply Voltage	2.5V
-3db Bandwidth	200MHz
On-State Resistance (Max)	4.5Ohm
Min Dual Supply Voltage	2.25V
High Level Output Current	30mA
Dual Supply Voltage	2.5V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	11pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	21ns, 10ns (Typ)
Charge Injection	5pC
Crosstalk	-67dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	35ns
Switch-off Time-Max	16ns
Max Junction Temperature (Tj)	150°C
Drain to Source Resistance	4.5Ohm
Height	1.2mm
Length	6.5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG734BRUZ Overview

Presented in 20-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Temperatures around -40°C~85°C TA are extended for operation. A total of 20 terminations have been recorded. Due to its 4 channels, the electrical component produces high-quality output. Powered by a 2.5V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 20 pins. Based on SPDT switching circuits, these analog multiplexers work. Try searching with ADG734 if you're looking for variants. There is 4.5Ohm internal resistance in this digital multiplexer. You can find the functions of the 20 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 1.8V. This digital switch can be operated with a current of 1nA. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 2.5V. For dual power supplies, a voltage of at least 2.25V should be attached. There are 160MHz bandwidths for data transfer. Drain to Source resistance is 4.5Ohm. The analogue multiplexer has 8 outputs.