AMC1200STDUBRQ1
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Max Power Dissipation | 44mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | AMC1200 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Operating Supply Current | 5.4mA |
| Nominal Supply Current | 5.4mA |
| Power Dissipation | 44mW |
| Output Current | 20mA |
| Amplifier Type | Isolation |
| Common Mode Rejection Ratio | 95 dB |
| Max Input Voltage | 250mV |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 100 kHz |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Supply Voltage Limit-Max | 6V |
| Power Consumption | 82.5mW |
| -3db Bandwidth | 0.1MHz |
| Dual Supply Voltage | 5V |
| Isolation Voltage | 4kV |
| Non-linearity-Max | 0.075% |
| Height | 4.85mm |
| Length | 9.5mm |
| Width | 6.57mm |
| Thickness | 3.3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SMD, Gull Wing |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
AMC1200STDUBRQ1 Overview
There is a 8-SMD, Gull Wing case package that contains the instrumentation amplifiers. An op amp ic of the Isolation type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. In total, there are 8 pins on this op amp ic. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. An 8-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 200μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~105°C . As long as the supply current of the chip does not exceed 5.4mA, this op amp ic can operate. The op amp ic has 1 channels on it. One of the many benefits of this op amp ic is that it emits Differential signals. The operating supply voltage of the buffer op amp is rated at 5.5V. To pack the operational amplifier ics, TR is adopted as the packing method. As the name implies, Automotive, AEC-Q100 refers to the series of the buffer op amp.
AMC1200STDUBRQ1 Features
8 Pins
supply voltage of 5V
Output Type: Differential
AMC1200STDUBRQ1 Applications
There are a lot of Texas Instruments AMC1200STDUBRQ1 Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Automation control systems
- Strain gauges
- Car stereo
- Automotive sensors
- Power transmission
- Gaming industry
- Multimedia playback equipment
- Weak signal detection
- Communication
