Parameters |
Voltage - Load |
1.5V~6V |
Telecom IC Type |
TELECOM CIRCUIT |
Rds On (Typ) |
80m Ω |
Height |
555μm |
Length |
1.88mm |
Width |
2.075mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-UFDFN Exposed Pad |
Number of Pins |
6 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e4 |
Feature |
Load Discharge, Slew Rate Controlled |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
200mOhm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Power Rating |
1.26W |
Max Power Dissipation |
750mW |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Current Rating |
2A |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
AP2280 |
Pin Count |
6 |
Number of Outputs |
1 |
Output Type |
P-Channel |
Max Output Current |
2A |
Voltage |
6V |
Interface |
On/Off |
Current |
2A |
Output Configuration |
High Side |
Power Dissipation |
750mW |
Output Current |
0A |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Input Type |
Non-Inverting |
Switch Type |
General Purpose |
Ratio - Input:Output |
1:1 |
AP2280-2FMG-7 Overview
A Tape & Reel (TR) is used to package it.This package is included in 6-UFDFN Exposed Pad.This lighting drivere has a mounting type of Surface Mount.General Purpose is the switch type it owns.Ensure reliable operation by setting the temperature to -40°C~85°C TA.It is possible to use 1 outputs in the lighting driver.A voltage of Not Required is used to power it.A maximum output voltage of P-Channel volts has been specified.Currently, the LED driving board is equipped with Load Discharge, Slew Rate Controlled features.There is a AP2280 family of things that it belongs to.As a result, there are 6 terminations.The 6 pins are used to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.To comply with the operation criteria, the maximum output current is reduced to 2A.Supply voltages of 5V allow for high efficiency.It is mounted in the way of Surface Mount.A total of 6 pins are present on it.The LED driver has 200mOhm resistance.This case results in a 0A output current.
AP2280-2FMG-7 Features
Supplied from 5V
Resistance of 200mOhm
AP2280-2FMG-7 Applications
There are a lot of Diodes Incorporated AP2280-2FMG-7 Power Switches ICs applications.
- Storage (HDDs, SSDs)
- Hard Disk Drives
- Smartphone and PDA
- HDD, SSD
- Wireless/Networking Cards
- Set-top-box
- PC Card Hot Swap
- USB3.1 Power Delivery
- Low Voltage I/O System Power
- Solid-State Drives