AP2281-3FMG-7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN Exposed Pad |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Feature | Load Discharge, Slew Rate Controlled |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 210mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 1.41W |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AP2281 |
| Pin Count | 6 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 2A |
| Interface | On/Off |
| Element Configuration | Single |
| Output Configuration | High Side |
| Power Dissipation | 1.41W |
| Output Current | 0A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 1 μs |
| Switch Type | General Purpose |
| Nominal Input Voltage | 6V |
| Turn-Off Delay Time | 500 ns |
| Continuous Drain Current (ID) | 2A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.5V~6V |
| Telecom IC Type | TELECOM CIRCUIT |
| Rds On (Typ) | 80m Ω |
| Drain to Source Resistance | 280mOhm |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
AP2281-3FMG-7 Overview
A Tape & Reel (TR) is used to package it.The 6-UFDFN Exposed Pad package contains it.Surface Mount is the mounting type of the LED driver.General Purpose is the switch type it owns.In order to guarantee reliable performance, the temperature should be set to -40°C~85°C TA.There are 1 outputs available on this lighting driver.Operation is based on a supply voltage of Not Required.A maximum output voltage of P-Channel volts has been specified.Load Discharge, Slew Rate Controlled features are available on the lighting driver.It is part of the AP2281 family of LED drivers.A total of 6 terminations have been found in it.The 6 pins are used to operate the LED driver.Currently, there are 1 functions associated with the lighting driver.To comply with the operation criteria, the maximum output current is reduced to 2A.A supply voltage of 5V leads to high efficiency.In this case, it is mounted in the way of Surface Mount.The LED driver has a total of 6 pins.The LED driver has 210mOhm resistance.This case has the output current set to 0A.
AP2281-3FMG-7 Features
Supplied from 5V
Resistance of 210mOhm
AP2281-3FMG-7 Applications
There are a lot of Diodes Incorporated AP2281-3FMG-7 Power Switches ICs applications.
- Low Voltage I/O System Power
- USB Ports/Hubs
- Wireless/Networking Cards
- PC Cards
- Wireless Modem Data Cards
- Storage Drives
- USB Protection
- Smart Phones, Feature Phones
- Various applications equipped with buttons
- PDAs
