ATV2500BQ-25DM/883
| Parameters | |
|---|---|
| Mount | Surface Mount, Through Hole |
| Package / Case | CDIP |
| Number of Pins | 44 |
| JESD-609 Code | e0 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 40 |
| ECCN Code | 3A001.A.2.C |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Frequency | 36MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 40 |
| JESD-30 Code | R-GDIP-T40 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of I/O | 24 |
| Memory Type | EPROM |
| Propagation Delay | 25 ns |
| Frequency (Max) | 36MHz |
| Programmable Logic Type | UV PLD |
| Screening Level | MIL-STD-883 Class B |
| Output Function | MACROCELL |
| Number of Macro Cells | 24 |
| JTAG BST | NO |
| Number of Dedicated Inputs | 13 |
| In-System Programmable | NO |
| Height Seated (Max) | 5.72mm |
| Length | 52.45mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ATV2500BQ-25DM/883 Overview
Currently, there are 24 macro cells, which are low-power cell sites (towers, antennas, masts) that serve as radio coverage.It is contained in package [0].It is programmed with 24 I/Os.The termination of a device is set to [0].DUALis the terminal position of this electrical part.The device is powered by a voltage of 5V volts.This part is part of the family [0].It is equipped with 40 pin count.High efficiency requires a voltage supply of [0].It is recommended to store data in [0].Surface Mount, Through Holeis the mounting point of this electronic part.The 44pins are designed into the board.A maximum supply voltage of 5.5Vis used in its operation.A minimum supply voltage of 4.5V is required for this device to operate.This device runs on 5Vvolts of electricity.A frequency of 36MHzcan be achieved.There should be a temperature above -55°Cat the time of operation.It is recommended that the operating temperature be below 125°C.Input signals are detected by 13dedicated inputs.It is recommended that the maximum frequency be less than 36MHz.There are several types of programmable logic that can be categorized as UV PLD.
ATV2500BQ-25DM/883 Features
CDIP package
24 I/Os
40 pin count
44 pins
5V power supplies
ATV2500BQ-25DM/883 Applications
There are a lot of Atmel (Microchip Technology) ATV2500BQ-25DM/883 CPLDs applications.
- Digital multiplexers
- Address decoders
- Wide Vin Industrial low power SMPS
- POWER-SAVING MODES
- Power automation
- PLC analog input modules
- Software-Driven Hardware Configuration
- Timing control
- Portable digital devices
- DDC INTERFACE
