banner_page

BTF3050TEATMA1

N-Channel PMIC 5 Pin 5V TO-252-5, DPak (4 Leads + Tab), TO-252AD


  • Manufacturer: Infineon Technologies
  • Nocochips NO: 376-BTF3050TEATMA1
  • Package: TO-252-5, DPak (4 Leads + Tab), TO-252AD
  • Datasheet: PDF
  • Stock: 896
  • Description: N-Channel PMIC 5 Pin 5V TO-252-5, DPak (4 Leads + Tab), TO-252AD (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case TO-252-5, DPak (4 Leads + Tab), TO-252AD
Number of Pins 5
Weight 329.988449mg
Operating Temperature -40°C~150°C TJ
Packaging Tape & Reel (TR)
Published 2014
Feature Slew Rate Controlled
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 4
Resistance 100mOhm
Terminal Position SINGLE
Terminal Form GULL WING
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 1
Supply Voltage 5V
Reach Compliance Code not_compliant
Time@Peak Reflow Temperature-Max (s) NOT SPECIFIED
JESD-30 Code R-PSSO-G4
Number of Outputs 1
Output Voltage 40V
Output Type N-Channel
Max Output Current 3A
Supply Voltage-Min (Vsup) 3V
Interface On/Off
Nominal Supply Current 2.5mA
Output Configuration Low Side
Voltage - Supply (Vcc/Vdd) Not Required
Input Type Non-Inverting
Switch Type General Purpose
Halogen Free Halogen Free
Drain to Source Voltage (Vdss) 40V
Nominal Input Voltage 5.5V
Ratio - Input:Output 1:1
Voltage - Load 40V Max
Max Dual Supply Voltage 40V
Fault Protection Current Limiting (Fixed), Over Temperature, Over Voltage
Output Peak Current Limit-Nom 3A
Rds On (Typ) 40m Ω
Turn Off Time 30 μs
Built-in Protections OVER VOLTAGE; THERMAL; TRANSIENT
Output Current Flow Direction SINK
Width 6.22mm
RoHS Status ROHS3 Compliant
Lead Free Contains Lead

BTF3050TEATMA1 Overview


It is package in Tape & Reel (TR) case.It is included in the package TO-252-5, DPak (4 Leads + Tab), TO-252AD.It has been mounted as Surface Mount on the LED driver.A General Purpose switch type is owned by it.It is best to set the temperature to -40°C~150°C TJ to ensure reliable operation.By default, it is set to output 1.Operation is based on a supply voltage of Not Required.The maximum output voltage is N-Channel volts.As far as features are concerned, the LED driving board has Slew Rate Controlled.In total, there are 4 terminations.The operation is performed through the 5 pins.It has 1 functions.The maximum output current is reduced to 3A to meet the operation criteria.The supply voltage can be 5V for high efficiency.It is positioned in the direction of Surface Mount.There is 100mOhm resistance on the LED driver.In order to operate normally, the supply voltage (Vsup) must be maintained above 3V.

BTF3050TEATMA1 Features


Supplied from 5V
Resistance of 100mOhm

BTF3050TEATMA1 Applications


There are a lot of Infineon Technologies BTF3050TEATMA1 Power Switches ICs applications.

  • Notebook and Tablet Computers
  • USB Protection
  • HDD, SSD
  • Notebook PC
  • Portable/Handheld Devices
  • Wireless Headsets
  • Solid-State Drives
  • Set-Top Boxes
  • Portable GPS Device
  • Low Voltage I/O System Power

Write a review

Note: HTML is not translated!
    Bad           Good