BTS410E2 E3062A
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | TO-263-5, D2Pak (4 Leads + Tab), TO-263BB |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart, Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Additional Feature | SEATED HGT-NOM; SEATED HGT-CALCULATED |
| Subcategory | Peripheral Drivers |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS410E2 |
| JESD-30 Code | R-PSSO-G4 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 42V |
| Power Supplies | 4.5/42V |
| Supply Voltage-Min (Vsup) | 4.7V |
| Interface | On/Off |
| Current - Output (Max) | 1.6A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.7V~42V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 1.8A |
| Rds On (Typ) | 190m Ω |
| Turn Off Time | 85 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 4.5mm |
| Width | 9.25mm |
| RoHS Status | Non-RoHS Compliant |
BTS410E2 E3062A Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).It is included with the TO-263-5, D2Pak (4 Leads + Tab), TO-263BB package as well.The LED driver is mounted as Surface Mount.It owns General Purpose switch type.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.By default, it is set to output 1.In order to operate, it requires a voltage supply of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.A lighting driver with Auto Restart, Status Flag features is available.The BTS410E2 family consists of this type.A total of 4 terminations have been recorded.It contains 1 functions.In terms of output, the lighting driver can provide a maximum of 1.6A V.Supply voltages of 12V allow for high efficiency.It is part of the PROFET? series.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.The maximum supply voltage is set to 42V.In order to operate normally, the supply voltage (Vsup) must remain above 4.7V.There is a voltage supply of 4.5/42V volts on this part.With this LED driver, SEATED HGT-NOM; SEATED HGT-CALCULATED can also be produced.
BTS410E2 E3062A Features
Supplied from 12V
Additional features like SEATED HGT-NOM; SEATED HGT-CALCULATED
BTS410E2 E3062A Applications
There are a lot of Infineon Technologies BTS410E2 E3062A Power Switches ICs applications.
- Telecom and Network Systems
- Hot Swaps
- Portable GPS
- Wireless/Networking Cards
- Solid-State Drives
- Notebook and Tablet Computers
- Hard Disk Drives
- USB Ports/Hubs
- USB Power Distribution
- Portable Video Game Players
