BTS410E2E3062ABUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-5, D2Pak (4 Leads + Tab), TO-263BB |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Last Time Buy |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Additional Feature | SEATED HGT-NOM; SEATED HGT-CALCULATED |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 50W |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| JESD-30 Code | R-PSSO-G4 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Voltage | 68V |
| Output Type | N-Channel |
| Supply Voltage-Min (Vsup) | 4.7V |
| Interface | On/Off |
| Current - Output (Max) | 1.6A |
| Nominal Supply Current | 5mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Switch Type | General Purpose |
| Halogen Free | Not Halogen Free |
| Nominal Input Voltage | 42V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.7V~42V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Output Peak Current Limit-Nom | 1.8A |
| Rds On (Typ) | 190m Ω |
| Turn Off Time | 85 μs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 4.5mm |
| Width | 9.25mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
BTS410E2E3062ABUMA1 Overview
Tape & Reel (TR) is how it's packaged.It is included in the package TO-263-5, D2Pak (4 Leads + Tab), TO-263BB.A Surface Mount mounting is used for the LED driving board.The switch type of this switch is General Purpose.It is recommended to set the temperature to -40°C~150°C TJ in order to ensure reliable operation.There are 1 outputs available on this lighting driver.Operation is based on Not Required supply voltage.It produces a maximum output voltage of N-Channel volts at its maximum output.It has a total of Auto Restart features.It consists of 4 terminations in total.The LED driver has 1 functions.In terms of output, the lighting driver can provide a maximum of 1.6A V.The supply voltage of 12V is conducive to high efficiency.Surface Mount is mounted in the way of this lighting driver.A component of this type is included in the PROFET? series.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.For normal operation, the supply voltage (Vsup) must be kept above 4.7V.Through the use of this lighting driver, we can also produce SEATED HGT-NOM; SEATED HGT-CALCULATED.
BTS410E2E3062ABUMA1 Features
Supplied from 12V
Additional features like SEATED HGT-NOM; SEATED HGT-CALCULATED
BTS410E2E3062ABUMA1 Applications
There are a lot of Infineon Technologies BTS410E2E3062ABUMA1 Power Switches ICs applications.
- Handheld Devices
- Wireless Modem Data Cards
- Portable/Handheld Devices
- Wireless/Networking Cards
- HDD, SSD
- Hot Swap
- Hard Disk Drives
- Portable GPS
- Storage (HDDs, SSDs)
- PC Cards
