CD74FCT374E
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74FCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | BICMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74FCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 48mA |
| Number of Bits | 8 |
| Clock Frequency | 70MHz |
| Propagation Delay | 6.6 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 6.6 ns |
| Family | FCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 15mA 48mA |
| Max Propagation Delay @ V, Max CL | 6.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 25.4mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74FCT374E Overview
As a result, it is packaged as 20-DIP (0.300, 7.62mm). A package named Tubeincludes it. There is a Tri-State, Non-Invertedoutput configured with it. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Through Hole. The JK flip flop operates with an input voltage of 4.75V~5.25V volts. Temperature is set to 0°C~70°C TA. This electronic flip flop is of type D-Type. JK flip flop belongs to the 74FCTseries of FPGAs. A frequency of 70MHzshould not be exceeded by its output. A total of 1elements are contained within it. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. Members of the 74FCT374family make up this object. Power is supplied from a voltage of 5V volts. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the FCTfamily. There is an electronic component mounted in the way of Through Hole. The electronic flip flop is designed with pins 20. The clock edge trigger type for this device is Positive Edge. This RS flip flops is a part number FF/Latches. There are 8bits in its design. Its flexibility is enhanced by 8 circuits. A power supply of 5Vis required to operate it. A total of 2ports are embedded in the D flip flop. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. As a result of its output current of 48mA, it is very flexible in terms of design. It is designed with 3 output lines. Quiescent current is consumed by the D latch in the amount of 8μA.
CD74FCT374E Features
Tube package
74FCT series
20 pins
8 Bits
5V power supplies
CD74FCT374E Applications
There are a lot of Texas Instruments CD74FCT374E Flip Flops applications.
- Shift Registers
- Single Up Count-Control Line
- Communications
- Dynamic threshold performance
- Cold spare funcion
- Instrumentation
- Storage Registers
- 2 – Bit synchronous counter
- Test & Measurement
- Asynchronous counter
