CD74HC574M
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 250 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 28ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HC574M Overview
The flip flop is packaged in a case of 20-SOIC (0.295, 7.50mm Width). A package named Tubeincludes it. This output is configured with Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. It is at -55°C~125°C TAdegrees Celsius that the system is operating. A flip flop of this type is classified as a D-Type. The 74HCseries comprises this type of FPGA. You should not exceed 60MHzin the output frequency of the device. In total, it contains 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74HC574family includes it. An input voltage of 4.5Vpowers the D latch. Its input capacitance is 10pF farads. In terms of electronic devices, this device belongs to the HC/UHfamily of devices. A part of the electronic system is mounted in the way of Surface Mount. A total of 20pins are provided on this board. This device's clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. The flip flop is designed with 8bits. Vsup reaches 6V, the maximal supply voltage. A normal operating voltage (Vsup) should remain above 2V. The system runs on a power supply of 2/6V watts. The flip flop has 2embedded ports. The 7.8mA output current allows it to be designed with the greatest amount of flexibility. In order for the chip to function, it has 3output lines. Quiescent current is consumed by the D latch in the amount of 8μA. Currently, there are 8 channels available.
CD74HC574M Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
CD74HC574M Applications
There are a lot of Texas Instruments CD74HC574M Flip Flops applications.
- Common Clocks
- Bus hold
- Modulo – n – counter
- Count Modes
- Balanced 24 mA output drivers
- Computers
- Dynamic threshold performance
- Single Up Count-Control Line
- Bounce elimination switch
- Pattern generators
