CD74HCT175M96
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latch |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Number of Bits | 4 |
| Clock Frequency | 25MHz |
| Propagation Delay | 33 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 4mA |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Prop. Delay@Nom-Sup | 53 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CD74HCT175M96 Overview
It is embeded in 16-SOIC (0.154, 3.90mm Width) case. Package Cut Tape (CT)embeds it. In the configuration, Differentialis used as the output. JK flip flop uses Positive Edgeas the trigger. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. A temperature of -55°C~125°C TAis used in the operation. This D latch has the type D-Type. The FPGA belongs to the 74HCT series. You should not exceed 25MHzin the output frequency of the device. The list contains 1 elements. There are 16 terminations,JK flip flop belongs to 74HCT175 family. The power supply voltage is 5V. There is 10pF input capacitance for this T flip flop. HCTis the family of this D flip flop. There is an electronic part that is mounted in the way of Surface Mount. This board has 16 pins. This device has Positive Edgeas its clock edge trigger type. There is a FF/Latchbase part number assigned to the RS flip flops. Flip flops designed with 4bits are used in this part. The superior flexibility of this circuit is achieved by using 4 circuits. This D flip flop is well suited for TR based on its reliable performance. The system runs on a power supply of 5V watts. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In terms of quiescent current, it consumes 8μA .
CD74HCT175M96 Features
Cut Tape (CT) package
74HCT series
16 pins
4 Bits
5V power supplies
CD74HCT175M96 Applications
There are a lot of Texas Instruments CD74HCT175M96 Flip Flops applications.
- Frequency Divider circuits
- Reduced system switching noise
- Memory
- Synchronous counter
- Digital electronics systems
- Bounce elimination switch
- Set-reset capability
- ATE
- Balanced Propagation Delays
- EMI reduction circuitry
