Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
48-TFSOP (0.240, 6.10mm Width) |
Number of Pins |
48 |
Weight |
223.195796mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
48 |
ECCN Code |
EAR99 |
Type |
PLL Clock Driver |
Subcategory |
Clock Drivers |
Packing Method |
TR |
Voltage - Supply |
2.3V~2.7V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
2.5V |
Terminal Pitch |
0.5mm |
Frequency |
220MHz |
Base Part Number |
CDCVF857 |
Pin Count |
48 |
Number of Outputs |
10 |
Operating Supply Voltage |
2.5V |
Supply Voltage-Max (Vsup) |
2.7V |
Supply Voltage-Min (Vsup) |
2.3V |
Number of Circuits |
1 |
Nominal Supply Current |
10mA |
Family |
857 |
Output Characteristics |
3-STATE |
Input |
SSTL-2 |
Ratio - Input:Output |
2:11 |
PLL |
Yes with Bypass |
Differential - Input:Output |
Yes/Yes |
Propagation Delay (tpd) |
3.5 ns |
Divider/Multiplier |
No/No |
Same Edge Skew-Max (tskwd) |
0.04 ns |
Height |
1.2mm |
Length |
12.5mm |
Width |
6.1mm |
Thickness |
1.15mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
CDCVF857DGGR Overview
As a clock IC, it uses the Tape & Reel (TR) package. This clock generator is embedded in the 48-TFSOP (0.240, 6.10mm Width) package. In the reflowing process, this clock generator ic is able to maintain a maximum temperature of 260. 48 terminations can be found in frequency generators. The supply voltage of 2.5V allows for high efficiency. In this case, SSTL-2 is designed to be the input of the clock generator. For full access to the electronic component's capabilities, 1 circuits are implemented. Thanks to the Surface Mount, this electric component can easily be installed on a panel. The maximal supply voltage this clock generator would take is 2.7V. Keeping the supply voltage for this frequency synthesizer above 2.3V is recommended for safety reasons. Clock generators should operate with the voltage supply of 2.3V~2.7V. Using the test statistics, it is estimated that the ambient temperature should be set to -40°C~85°C. An electrical part such as this one can be classified as a PLL Clock Driver component. It is a 48-bit IC that is designed for microprocessors specifically. These related electrical parts are available for the base part number CDCVF857. The clock PLL has 48 pins that are available. There is a maximum supply voltage of 2.5V that electronic frequency generator can handle. In general, this clock PLL is considered a Clock Drivers device. Clock PLL is configured with 10 output. The timing skew of this frequency synthesizer is low at 0.04 nsmax. A search for the 857 family will yield similar electronic parts. At frequencies of 220MHz, RF synthesizer achieves high efficiency. TR is an ideal package for this electronic frequency generator.
CDCVF857DGGR Features
Available in the 48-TFSOP (0.240, 6.10mm Width)
Supply voltage of 2.5V
Operating supply voltage of 2.5V
CDCVF857DGGR Applications
There are a lot of Texas Instruments CDCVF857DGGR Clock Generators applications.
- Wireless handsets
- Skew suppression
- Sampling clocks for ADC and DAC
- FSK demodulators
- Radio receivers
- FMCW Radar
- Clock synchronization
- Communication infrastructure
- Simple clock clean-up circuits
- Infotainment systems