CLVC1G175MDCKREPG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 2.494758mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LVC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 1.65V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G175 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3.3V |
| Number of Circuits | 1 |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 175MHz |
| Propagation Delay | 8 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 1.5 ns |
| Family | LVC/LCX/Z |
| Current - Output High, Low | 32mA 32mA |
| Max I(ol) | 0.032 A |
| Max Propagation Delay @ V, Max CL | 5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CLVC1G175MDCKREPG4 Overview
As a result, it is packaged as 6-TSSOP, SC-88, SOT-363. It is contained within the Tape & Reel (TR)package. As configured, the output uses Non-Inverted. In the configuration of the trigger, Positive Edgeis used. Surface Mountmounts this electrical part. The JK flip flop operates at 1.65V~5.5Vvolts. A temperature of -55°C~125°C TAis used in the operation. It belongs to the type D-Typeof flip flops. In this case, it is a type of FPGA belonging to the 74LVC series. There should be no greater frequency than 175MHzon its output. 6terminations have occurred. You can search similar parts based on 74LVC1G175. Power is provided by a 1.8V supply. This JK flip flop has a 3pFfarad input capacitance. An electronic device belonging to the family LVC/LCX/Zcan be found here. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 6. There is a clock edge trigger type of Positive Edgeon this device. This part is included in FF/Latches. It is designed with a number of bits of 1. It reaches the maximum supply voltage (Vsup) at 5.5V. Its flexibility is enhanced by 1 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. An electrical current of 3.3V volts is applied to it. It consumes a total of 10μA quiescent current at any given time.
CLVC1G175MDCKREPG4 Features
Tape & Reel (TR) package
74LVC series
6 pins
1 Bits
3.3V power supplies
CLVC1G175MDCKREPG4 Applications
There are a lot of Texas Instruments CLVC1G175MDCKREPG4 Flip Flops applications.
- Computers
- Data transfer
- Latch
- Counters
- Consumer
- Patented noise
- Guaranteed simultaneous switching noise level
- Frequency Divider circuits
- Frequency Dividers
- Bounce elimination switch
