CY2308SC-1
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| Type | Fanout Buffer (Distribution), Zero Delay Buffer |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Reach Compliance Code | not_compliant |
| Frequency | 133MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CY2308 |
| Output | LVCMOS |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 45mA |
| Frequency (Max) | 133.3MHz |
| Input | LVCMOS, LVTTL |
| Ratio - Input:Output | 1:8 |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Same Edge Skew-Max (tskwd) | 0.2 ns |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
CY2308SC-1 Overview
As a clock IC, PLLs is packaged using the Tube method. There is a clock generator embedded in the 16-SOIC (0.154, 3.90mm Width) package. Frequency generator is capable of operating at a maximum temperature of 240 when reflowing. 16 terminations can be found in frequency synthesizer. This time clock generator should be voltaged at 3.3V. LVCMOS, LVTTL is designed for clock generator's input. For full access to the electronic component's capabilities, 1 circuits are implemented. It provides a maximum frequency of 133.3MHz. Because of the Surface Mount, clock PLL can be easily mounted on the panel. This clock generator would require a maximum supply voltage of 3.6V. A maximum voltage of 3V should be used for this frequency generator for safety reasons. As long as you provide 3V~3.6V supply voltage, it will work. Based on test statistics, ambient temperature should be set at 0°C~70°C. It's compatible with LVCMOS logic levels. A Fanout Buffer (Distribution), Zero Delay Buffer is a classification for the electronic part in question. Microprocessor-specific clock PLL with 16 bits. This part number is related to its related electronic parts. There are 16 pins that are available on the clock PLL. The supply voltage should be maintained at 3.3V for high efficiency. In general, this clock PLL is considered a Clock Drivers device. The frequency synthesizer features 8 signal outputs to ensure as high a frequency as possible. At 0.2 ns Max, this clock generator offers low timing skew. Frequency generator is able to reali133MHze high efficiency when operating at a frequency of 133MHz.
CY2308SC-1 Features
Available in the 16-SOIC (0.154, 3.90mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CY2308SC-1 Applications
There are a lot of Cypress Semiconductor Corp CY2308SC-1 Clock Generators applications.
- HDD recorders
- Telecommunication systems
- Pagers
- CB radios
- Main oscillator in receiver
- Frequency Modulation (FM) stereo decoders
- VSAT (Small Ground Satellite Station)
- Microwave radio
- High-frequency induction heating
- Time to digital converters
