CY74FCT2374CTQCTE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 5.2 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 5.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY74FCT2374CTQCTE4 Overview
The flip flop is packaged in a case of 20-SSOP (0.154, 3.90mm Width). It is contained within the Tape & Reel (TR)package. Tri-State, Non-Invertedis the output configured for it. It is configured with the trigger Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A voltage of 4.75V~5.25Vis required for its operation. In this case, the operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74FCTseries of FPGAs. You should not exceed 250MHzin the output frequency of the device. In total, it contains 1 elements. T flip flop consumes 200μA quiescent energy. It has been determined that there have been 20 terminations. The object belongs to the 74FCT2374 family. A voltage of 5V is used to power it. The input capacitance of this JK flip flopis 5pF farads. Devices in the FCTfamily are electronic devices. It is mounted by the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device has the base part number FF/Latches. It is designed with a number of bits of 8. It reaches 5.25Vwhen the maximum supply voltage (Vsup) is applied. The supply voltage (Vsup) should be maintained above 4.75V for normal operation. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. There are 5V power supplies attached to it. The D flip flop has no ports embedded. With an output current of 12mA, it is possible to design the device in any way you want. To operate, the chip has a total of 3 output lines. Currently, there are 8 input lines present.
CY74FCT2374CTQCTE4 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374CTQCTE4 Applications
There are a lot of Texas Instruments CY74FCT2374CTQCTE4 Flip Flops applications.
- Balanced 24 mA output drivers
- 2 – Bit synchronous counter
- QML qualified product
- Buffered Clock
- Dynamic threshold performance
- Functionally equivalent to the MC10/100EL29
- Individual Asynchronous Resets
- Set-reset capability
- Shift Registers
- Control circuits
