DG1411EN-T1-GE4
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.8Ohm |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG1411 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 24V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~24V ±4.5V~15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 15V |
| -3db Bandwidth | 210MHz |
| On-State Resistance (Max) | 1.8Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 550pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 24pF |
| On-state Resistance Match-Nom | 0.08Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | -20pC |
| Channel-to-Channel Matching (ΔRon) | 80m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switch-on Time-Max | 510ns |
| Switch-off Time-Max | 380ns |
| Height Seated (Max) | 0.95mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG1411EN-T1-GE4 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-VQFN Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -40°C~125°C TA. In total, there have been 16 terminations. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. A SPST - NC switching circuit is used for these analog switches. The multiplexer consists of 4 circuits. If you are looking for variants of the digital switch, trying search with DG1411. An switch multiplexer with 1.8Ohm internal resistance has a value of 1.8Ohm. For functions related to 16 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 24V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 4.5V should be applied to the electronic component. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 15V. In the case of dual power supplies, you should connect at least 4.5V.
DG1411EN-T1-GE4 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 210MHz
DG1411EN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG1411EN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Video switching
- Microprocessor controlled systems
- Ultrasound
- Cable PC
- T1/E1 Terminals
- Medical systems
- Access Concentrators
- Communication systems
- Mechanical reed relay replacement
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
