DG405BDY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 55Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG405 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DPST |
| Operating Supply Current | 1mA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 60pC |
| Crosstalk | -94.8dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG405BDY-T1-E3 Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, there are 16 terminations. A electrical component with 2 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. Multiplexers built on a SPST - NO switching circuit are built. Try searching for DG405 variants of the analog switch ic. As far as internal resistance is concerned, it has 55Ohm. The datasheets for the 16 pins explain the functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 13V. It would be sufficient to run this analogue multiplexer with 1mA current. If you put voltage higher than 500μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. With a DPST analog IC integrated into the board. 15V operating voltages can be used with this electrical part. Multiplexer ics with 4 outputs are available.
DG405BDY-T1-E3 Features
2 Channels
Switch Circuit: SPST - NO
1mA Supply Current
DG405BDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG405BDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Fiber In The Loop (FITL)
- Audio signal routing
- Ultrasound
- Communication systems
- Channel Banks
- High-Voltage
- Cellular phones
- Audio and video routing
- MP3 players
