DG408DQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG408 |
| Pin Count | 16 |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Propagation Delay | 160 ns |
| Turn On Delay Time | 150 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 12V ±5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 26pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height | 920μm |
| Length | 5.07mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG408DQ-T1-E3 Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 8 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the electrical part body. 1 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with DG408 if you are looking for variants. As far as internal resistance is concerned, it has 100Ohm. You can find the functions of the 16 pins in the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 44V. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 13V. For this multiplexer to operate, 1μA current would be sufficient. If put voltage greater than 500μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 5V. Operating voltages range from 36V.
DG408DQ-T1-E3 Features
8 Channels
1μA Supply Current
DG408DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG408DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- FTTH
- Cable PC
- Multi-Line E1 Interface Cards
- New designs requiring multiplexer functions
- Digital cross connects (DSX-1)
- Cellular phones
- Ultrasound
- Digital Cross-Connects
- PDH Multiplexers
