DG428DJ-E3
| Parameters | |
|---|---|
| Nominal Supply Current | 100μA |
| Power Dissipation | 900mW |
| Max Supply Current | 100μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 225ns |
| Signal Current-Max | 0.03A |
| Length | 37.4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 18-DIP (0.300, 7.62mm) |
| Number of Pins | 18 |
| Weight | 1.270087g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| Resistance | 150Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 900mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG428 |
| Pin Count | 18 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Leakage Current | 1μA |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 20μA |
DG428DJ-E3 Overview
Due to its 18-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, you'll find this switch device. 8:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. Totally, there are 18 terminations. As a result of its 8 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 18 series that this electronic component is included. There are 1 circuits in this switch device. Try searching with DG428 if you're looking for variants. A 150Ohm internal resistance characterizes this multiplexer. To find out what the functions of 18 pins are, please refer to their datasheets. normally, users should not supply switches with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 13V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 20μA current. Putting voltage greater than 100μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. When using dual power supplies, you should attach at least 7V.
DG428DJ-E3 Features
8 Channels
20μA Supply Current
DG428DJ-E3 Applications
There are a lot of Vishay Siliconix DG428DJ-E3 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Fiber to the Home
- Cell phones
- Automotive applications
- DSLAMs
- PCMCIA cards
- SDH
- T1/E1 Terminals
- Communications systems
- E1 Multiplexer
