DG445CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG445 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -10V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 170ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG445CJ+ Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around 0°C~70°C TA. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 10V voltage supply. This electrical component is included in the 16 series of products. Circuits based on SPST - NO switching are used to construct these analog switch ics. A 4 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with DG445. The internal resistance of this digital multiplexer is 85Ohm. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 20V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. A voltage higher than 1μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG445CJ+ Features
1 Channels
Switch Circuit: SPST - NO
DG445CJ+ Applications
There are a lot of Maxim Integrated DG445CJ+ Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Residential Gateways, Home Gateway/Router
- Isolation
- Channel Banks
- DSUs
- Fault Tolerant Systems
- Microprocessor controlled systems
- CSU
- Avionics
- Microwave transmission systems
