banner_page

DS1099U-CC+

5V Clock Generator DS1099 Clock Generators EconOscillator? Series 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) 8 Terminals Surface Mount 2.7V~5.5V Tube


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-DS1099U-CC+
  • Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
  • Datasheet: PDF
  • Stock: 951
  • Description: 5V Clock Generator DS1099 Clock Generators EconOscillator? Series 8 Pins 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) 8 Terminals Surface Mount 2.7V~5.5V Tube (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins 8
Operating Temperature -40°C~125°C
Packaging Tube
Published 2006
Series EconOscillator™
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Type Clock Generator
Terminal Finish Matte Tin (Sn)
Voltage - Supply 2.7V~5.5V
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Supply Voltage 5V
Terminal Pitch 0.65mm
Frequency 262kHz
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number DS1099
Output CMOS, TTL
Pin Count 8
Number of Circuits 1
Input Clock
Ratio - Input:Output 1:2
Primary Clock/Crystal Frequency-Nom 1MHz
PLL No
Differential - Input:Output No/No
Divider/Multiplier Yes/No
Length 3mm
Width 3mm
RoHS Status ROHS3 Compliant
Lead Free Lead Free

DS1099U-CC+ Overview


Tube-method packaging is used for clock ICs. The 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package contains this clock generator. The frequency generator is capable of withstanding a maximum temperature of 260 during reflowing. In it, there are 8 terminations to be found. The clock generator ic should be grounded with a voltage of 5V. In this clock generator, Clock is used as the input to the clock. An implementation of 1 circuits is required in order to fully utili1e the capabilities of the electrical part. Thanks to the Surface Mount, this electric component can easily be installed on a panel. As far as the supply voltage is concerned, clock PLL can be used with 2.7V~5.5V. As determined by the test statistics, the ambient temperature should be set to -40°C~125°C. CMOS, TTL logic levels are supported by this RF synthesizer. It has been classified as a Clock Generator electronic part, which means that it is a semiconductor. Microprocessor-specific clock PLL with 8 bits. You can find related electrical components to the base part number DS1099. There are a number of 8 pins that are available on the clock generators. This electronic part is a member of the EconOscillator? series. High efficiency is achieved when operating at a frequency of 262kHz.

DS1099U-CC+ Features


Available in the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Supply voltage of 5V

DS1099U-CC+ Applications


There are a lot of Maxim Integrated DS1099U-CC+ Clock Generators applications.

  • Bluetooth receivers
  • Simple clock clean-up circuits
  • Closed circuit systems
  • Electronic countermeasures
  • Digital switching systems
  • Clock synchronization
  • Bit synchronization
  • Vector network analyzers (VNA)
  • High-frequency induction heating
  • DVD recorders

Write a review

Note: HTML is not translated!
    Bad           Good