FSA2467MPX
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 32pF |
| On-state Resistance Match-Nom | 0.03Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 32ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω (Min) |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 750μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 126mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 400mOhm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 85MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | FSA2467 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 100nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 50 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Bandwidth | 85MHz |
| Turn-Off Delay Time | 32 ns |
| On-State Resistance (Max) | 400Ohm Typ |
| High Level Output Current | 350mA |
| Multiplexer/Demultiplexer Circuit | 2:2 |
FSA2467MPX Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WFQFN Exposed Pad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:2. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. The electronic part delivers high-quality output through its 2 channels. With a 2.3V voltage supply, the electrical component should be turned on and run. On the other hand, analog switches can be constructed using DPDT switching circuits. Try searching with FSA2467 if you're looking for variants. A 400mOhm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 4.3V. An effective Single supply digital multiplexer. 1.65V should be the lowest voltage fed to the electronic component. An analogue multiplexer drains from a single voltage supply at 1.65V~4.3V. When the digital multiplexer is charged above 100nA, damage can occur. It can operate from 3V operating voltages. The 4 inputs need to be operated in order to work. There are 85MHz bandwidths for data transfer. This digital multiplexer has 8 outputs.
FSA2467MPX Features
2 Channels
Switch Circuit: DPDT
Bandwidth: 85MHz
FSA2467MPX Applications
There are a lot of ON Semiconductor FSA2467MPX Analog Switches & Multiplexers ICs applications.
- SDH
- Avionics
- PBXs
- RGB switches
- PDAs
- Relay Replacement
- Avionics test equipment
- Sample hold systems
- Multi-Line E1 Interface Cards
- Microprocessor Controlled Analog Systems
