Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-UFDFN |
Number of Pins |
6 |
Weight |
30g |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
ECCN Code |
EAR99 |
Resistance |
360mOhm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
180mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Number of Functions |
1 |
Supply Voltage |
2.3V |
Terminal Pitch |
0.5mm |
Base Part Number |
FSA5157 |
Output |
SEPARATE OUTPUT |
Number of Channels |
1 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.65V |
Nominal Supply Current |
30nA |
Power Dissipation |
180mW |
Max Supply Current |
100nA |
Number of Bits |
2 |
Turn On Delay Time |
70 ns |
Number of Inputs |
1 |
Supply Type |
Single |
Bandwidth |
80MHz |
Turn-Off Delay Time |
40 ns |
On-State Resistance (Max) |
360mOhm Typ |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
10nA |
Channel Capacitance (CS(off), CD(off)) |
21pF |
On-state Resistance Match-Nom |
0.12Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
55ns, 30ns |
Charge Injection |
6pC |
Channel-to-Channel Matching (ΔRon) |
40m Ω |
Crosstalk |
-75dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.65V~4.3V |
Height |
500μm |
Length |
1.45mm |
Width |
1mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
FSA5157L6X Overview
The electrical component comes in 6-UFDFN packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there have been 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. A 2.3V voltage supply should turn on and run the electronic component. A SPDT switching circuit is used for these analog switches. FSA5157 can be used to search for analog multiplexer variants. It has an internal resistance of 360mOhm. The functions of 6 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. 1.65V should be the lowest voltage fed to the electronic component. Using only a single voltage supply, this analog switch requires 1.65V~4.3V voltage. The analogue multiplexer may be damaged if voltage is greater than 100nA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The 1 inputs need to be operated in order to work. 80MHz bandwidths enable data to be transferred. The switch device is capable of conducting in a 2-bit mode.
FSA5157L6X Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 80MHz
2-Bit
FSA5157L6X Applications
There are a lot of ON Semiconductor FSA5157L6X Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Data Acquisition Systems
- Channel Banks
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH
- Fiber to the Home
- Avionics test equipment
- Video signal routing
- Private Branch Exchange (PBX)
- Automotive applications